2024 Author: Erin Ralphs | [email protected]. Last modified: 2024-02-19 11:42
The heater of a car is not called a stove for nothing, because it is designed to make the driver and passengers feel comfortable in the cabin, regardless of the ambient temperature. A malfunction of this device can cause a lot of trouble. And it's not just about comfort. The stove, in addition to its main function - heating, also serves to blow the windshield. And this is very important, especially on frosty days. Without it, the driver will have a very difficult time.
In this article we will talk about one of the main elements of the stove - the fan. We will consider why it is needed, what it is, for what reasons it fails and how it is repaired or replaced.
Design of the "fourteenth" heater
VAZ-2114 stove consists of the following elements:
- plastic case;
- heater radiator;
- fan.
As you can see, the list is small. In addition, in the event of any malfunction, the replacement of the VAZ-2114 stove assembly will not be required, since each ofits elements can be replaced individually.
Heater operation principle
The heater itself does not produce heat. As its carrier, heated coolant is used, which enters the stove radiator. In the process of heat exchange, the air inside the device heats up and begins to penetrate into the cabin through special nozzles. However, natural circulation is not enough to warm up the interior of the car. The supply of warm air under pressure is carried out by a fan. It is thanks to him that the interior of the car warms up in a matter of minutes.
What is a heater fan
The VAZ-2114 stove fan is a conventional DC electric motor powered by the car's on-board network. The air flow is created by the rotation of a cylindrical impeller mounted on the armature shaft.
The fan is controlled by a special switch located on the control panel. It has four positions corresponding to its operating modes: "OFF" mode and three speeds. The faster the rotation of the impeller, the stronger the flow of air supplied to the passenger compartment.
Heater fan malfunctions
In VAZ-2114 cars, the stove fan can be replaced both as part of routine maintenance and when critical malfunctions are detected. The device does not belong to the list of the most frequently broken, but still problems happen with it. The most "popular" breakdowns include:
- weararmature bearings;
- brush wear;
- destruction of the brush commutator;
- open or short circuit in the armature (stator) windings.
Don't rush to dismantle
Having found that the fan of the VAZ-2114 stove is not working, do not rush to dismantle and disassemble the heater. First you need to check the electrical circuit of the device, namely:
- fuse;
- mode switch resistor;
- wiring.
If the fan of the VAZ-2114 stove does not work, first of all we check the fuse. It is located in the main mounting block and is indicated on the diagram as F-7 (30 A). We remove it from the landing nest and “ring” it with a tester. If necessary, we change.
The next step is to diagnose the switch resistor. With the ignition on, turn the switch knob to the position corresponding to the third speed. If the fan is running, change the resistor.
Checking the wiring is to measure the voltage supplied to the device. Here you need to raise the hood, find the connector with the wires going to the fan, connect the voltmeter probes to them and take measurements by switching modes with the ignition on. There is voltage - the reason is in the electric motor itself, no - it is better to contact an auto electrician to diagnose the wiring.
Bearing wear
A sign of worn fan motor bearings is a characteristic hum. At the initial stage of a malfunction, this phenomenon usually does not affect the operation of the device, but withover time, it will definitely turn into a more serious problem. Therefore, noticing that the fan of the VAZ-2114 stove is buzzing, hurry up to lubricate the bearings.
Brush wear and collector destruction
Brushes bring electric current to the motor armature. They are made of graphite and are naturally subject to wear. If the electric motor is operating normally, they can last for 50-70 thousand kilometers. However, the influence of various negative factors reduces the service life of the latter by several times.
Destruction of the collector is most often the result of wear or misalignment of the brushes. Restoring this element is quite problematic even for a specialist, therefore, if a similar problem is discovered, then for the VAZ-2114, replacing the stove fan will become inevitable.
Open or short windings
The situation is even more complicated with windings. If a collector malfunction can be detected visually, then here it will be necessary to measure the resistance in different areas, and even then it is not a fact that after the problem is detected, it can be eliminated by rewinding. The best option in this case for the VAZ-2114 is to replace the stove fan. In addition, the new device will not cost so much. An electric motor with an impeller costs about 1100 rubles, with a casing - 1300 rubles.
How to remove the stove fan on the VAZ-2114
In order to repair or replace the fan motor, it will need to be removed. This can be done in two ways: by dismantling the heater assembly or by removing only the motor.
In the first case, you will have to disassemble the interior plastic, drain the refrigerant, disconnect the heating radiator from the cooling system, etc. Such dismantling can only be justified in one case - when you need to replace the VAZ-2114 stove assembly. If you do not plan anything like this, the fan can be removed from the side of the engine compartment. The procedure is as follows:
- Raise the hood, find the casing of the stove fan VAZ-2114. It is located under the windshield. You'll recognize it by its rounded shape and the black plastic it's made of.
- Unscrew 2 screws and 2 bolts, with which the casing is attached to the body of the stove.
- Disconnect the power wire connectors.
- With a thin slotted screwdriver or a knife, open the latches of the halves of the casing. Disconnect the halves, remove them to the side.
- We turn the fan so that it can pass between the side of the engine compartment and the decorative grille. Removing the device.
How to replace the fan
On the VAZ-2114, replacing the stove fan will not cause any difficulties. Especially if you have already dismantled the faulty device. The first step is to check the fan. To do this, lay it on a flat surface and bring two wires from the battery to the connector. Has the electric motor started? Then connect the device to the "native" connector of the wires going to the engine compartment from the passenger compartment. Turn on the ignition, and then the mode switch. Check if it worksfan in all its positions. After that, place the electric motor in its place and close the casing. Screw the casing to the heater body. Connect the power wires. Additionally, check the operation of the device.
Recommended:
How to drain gasoline from a car tank? Accessories and step by step instructions
Probably, there is not a single driver who did not get into such trouble as having to drain the fuel from the car's tank. It is very important to perform this action according to the safety regulations, and also to know which of the existing methods is suitable for your car
Do-it-yourself plastic car parts repair: methods and step-by-step instructions
Repair of plastic car parts: methods, instructions and preparation. Where can I repair plastic parts in the car. How to repair plastic in the car yourself. Do-it-yourself repair of plastic car body parts. Professional repair of plastic car products in St. Petersburg and Moscow
How to drive an ATV: step by step instructions, driving features
Quad bikes are getting more and more popular year after year. People have felt very well all the advantages of this technique and now they buy them (ATVs) without fear. Prices for this category of equipment are very biting, but this does not stop lovers of cross-country driving! But there are some nuances in all this. How to drive an ATV? Today we will learn everything about this issue and not only about it
Tightening the cylinder head: step by step instructions, features, device, tips from the masters
The cylinder head plays an essential role in the operation of the engine. Its correct position affects the operation of the gas distribution mechanism. Also, together with the cylinder block, it forms the combustion chambers. Therefore, when repairing, the correct tightening of the cylinder head is important
Noise isolation "Chevrolet Niva": step-by-step instructions with a description, materials used, reviews
The car "Chevrolet Niva" replaced the VAZ 2121 and its modifications, as a more advanced model. Having retained the excellent off-road characteristics of the Niva 4x4 and having acquired a new appearance, he began to be in demand among people who value comfort. Along with the improvements, a number of shortcomings inherent in domestic cars migrated to the new model. Including noise in the cabin. This article will tell you how to make soundproofing of the Chevrolet Niva