Homemade SUV: how to do it yourself?

2024 Author: Erin Ralphs | [email protected]. Last modified: 2024-02-19 11:42

For the inhabitants of our country, as well as citizens of the post-Soviet space, it is common to reinvent the wheel. This applies to devices that are expensive to buy, but it is quite possible to create with your own hands. Devices that dozens of designers are working on can be created independently. This requires minimal knowledge, desire and imagination. For example, it is quite possible to make a home-made SUV from regular models of domestic cars.

Homemade SUVs based on UAZ

It is not so difficult to make a car of this brand unrecognizable with your own hands. For cardinal changes you will need:

• Set of aluminum sheets with corrugated edging for sheathing.
• Metal and rubber pads.
• Fixing screws.
• Synthetic rugs.
• Foam.
• Triplex glass.
• Flexible plastic.
• Tools (wrenches, screwdrivers, accessories).

A home-made SUV with the correct performance of all manipulations on the characteristics will come out no worse than expensive counterparts.

Where to start?

First, you should take care ofstrengthening the outer skin and frame of the car. It is best to use steel pipes designed for high loads. It is also necessary to take into account the provision of insulation from moisture, especially if you plan to create not just an SUV, but a swamp.

If it is impossible to weld pipes, you can use the original UAZ body. Sometimes it is modified, giving the desired configuration. Mandatory strengthening will require side racks, roof and bottom.

Sheathing

A home-made SUV from a UAZ car is made after removing the old trim. Simultaneously with the strengthening of the hull, a new aluminum alloy structure is mounted, which is resistant to weather and corrosion. When choosing sheets, you should select a material whose thickness is not less than one and a half millimeters. The new skin is fastened with screws, which are fixed in the frame with special heads. To smooth out all the bumps and remove backlash, use rubber pads.

If the new case is installed incorrectly, a completely vulnerable design to mechanical and natural influences may come out. Therefore, the installation of the skin should be carried out carefully and carefully, checking all the steps, since this part is the most finicky when creating a do-it-yourself jeep based on UAZ.

Features

When making a homemade SUV, you need to pay attention to the camber when assembling the axle, you should first weld the lower elements of the bearings. Then they are mounted on the frame by means ofbolt fastening. Taking into account the peculiarities of operation, the type of wheels or even tracks is selected.

Torque is transmitted through the cardan shaft from the power unit to the rear axle. Such a node is beneficial in that it is easy to maintain and repair. First you need to make sure that the landing nests match with each other. Otherwise, turn out the required number of holes.

In conclusion, the updated machine will need to be tested several times. After finding problem areas, they must be checked and all problems fixed so that driving a homemade SUV is safe. Almost the entire modernization process is carried out according to a single scheme. From the original, only the power unit and body will be needed.

Homemade SUV from Oka

For regions with difficult roads, it is quite possible to make a swamp vehicle even from a small car. In the process, you can use various improvised means, ranging from spare parts of a broken car, ending with pipe cuts and metal sheets.

Universal equipment based on pneumatics or on wheels with low pressure is in great demand among craftsmen. Creating a jeep based on the Oka is a very profitable solution in terms of finances and practicality.

Stages of work

Homemade SUVs, the photo of which is presented above, can be made from the Oka, observing thissequence:

1. Choose the basis for the new vehicle. It could just be a frame from an IZH or Ural motorcycle.
2. Make the rear axle and suspension. At this stage, a strut is used, connected by parts of the spars.
3. By fixing the strut and steering sleeve, a single suspension unit is created.
4. As wheels, you can use cameras from trucks, which are attached using an adapter hub.
5. After mounting the frame and suspension, an updated engine, brake system and transmission are installed.

What to pay special attention to?

Above we looked at how to make a homemade SUV? Despite all the advantages, this technique has certain disadvantages. In particular, low-pressure chambers cause a lot of trouble. Although they do not require service, the elements become less maneuverable during operation.

It is also difficult to equip them with protection from flying dirt, since the dimensions are significantly larger than standard wheels.

As practice shows, pneumatics on homemade all-terrain vehicles are less practical than tracks. Otherwise, a home-made SUV based on the Oka or UAZ is economically viable and convenient, given the aspect that its design can be adjusted, depending on the characteristics of operation and climatic factors.

First of all, this technique is suitable for residents of rural areas and lovers of extreme off-road tourism.