2024 Author: Erin Ralphs | [email protected]. Last modified: 2024-02-19 11:42
The manufacturer establishes a maintenance schedule, within the framework of which the brake pads are replaced on the Hyundai Solaris. To perform the replacement, it is not necessary to visit the service station. This procedure can be done by hand. It is important to always check the condition of the brake system - safety depends on it. We will also consider the prices for this service in the service station of Moscow.
When to change?
The manufacturer does not give a clear regulation on the timing of the replacement of the front brake pads on the front wheels. The driver himself must monitor their wear. But the pads must be changed if there was a disc replacement, oil got on the friction linings, deep grooves appeared on the working surface as a result of operation, cracks, chips. Also, the replacement of brake pads on the Hyundai Solaris is carried out in case of detachment of the friction linings from the metalblock bases. In practice, the period from replacement to replacement on average for the front wheels is 30 thousand kilometers. For rear drum pads, the service life is twice as long. However, the wear rate depends on a lot of different factors.
The inner pads have an acoustic wear indicator. During braking, a characteristic rattle is heard. This means that the pad is worn to the limit. The front pads on this car model are changed only as a set. If you replace a pair of pads on only one side, then the car may pull to the side during braking.
Causes of accelerated wear
The wear rate is most often affected by two factors. The first is the illiterate operation of the brake system. Given the fact that the Hyundai Solaris is equipped with a relatively powerful engine, most drivers prefer a more aggressive driving style. Hard acceleration forces the driver to press the brake pedal more often. Aggressive driving results in faster pad wear. Also, most modern drivers have no idea about engine braking, and this technique allows you to increase the time for replacing brake pads on a Hyundai Solaris by two or more times.
The second factor is an attempt to save money and the installation of cheap pads, where unsuitable materials were used for the production of friction linings. These pads have a shorter lifespan. In addition, due to low-quality pads, discs and drums wear out faster.
How to know what to doreplacement?
A novice driver can understand that they need to replace the brake pads on the Hyundai Solaris by the following signs. If a set of alloy wheels is installed on the machine along with disc brakes, then the state of the pads can be conveniently observed through the slots in the discs. Wear will be clearly visible. Another simple option is sensors or wear indicators. They are electronic and mechanical. If an electronic sensor is installed, the corresponding light on the instrument panel will light up.
You can determine the wear of the pads by the level of the brake fluid. If there are no leaks in the system, and the fluid level in the expansion tank has dropped, then this may be caused by worn pads. The stroke of the pistons due to thinner pads is increased, so the level drops.
Also, worn pads will show a beating on the steering wheel when braking. This occurs due to deformation of the pads or discs. If, during acceleration to 80 kilometers per hour and sudden braking, the car pulls to the side and there is a beating on the brake pedal, then you need to replace the brake pads and discs with the Hyundai Solaris. Don't delay with this.
Step by step instructions for changing the front pads
Let's see how do-it-yourself front pads change in the garage using a set of standard tools. The first step is to dismantle the wheels. Then you need to insert a flat screwdriver with a wide blade into the window in the caliper between the pads and the disc. Thus, the brake pads are bred and the piston is sunk into the cylinder. Next, the bolts are unscrewed with a 14 wrenchfastening the caliper to the finger. Then the caliper is removed from the guides. It is not necessary to disconnect the brake hose. The caliper is tied to a spring. Next, the outer block is removed from the guide, and the inner block is pulled out in the same way. Prying with a screwdriver, take out the guide plates.
Next, you should install new pads, but before that you need to press the piston into the cylinder as much as possible. This is how the front brake pads are replaced on the Hyundai Solaris. This procedure can be done by hand in an hour.
Rear pads
First you need to remove the rear wheel and use a 14 key to unscrew the bolt securing the caliper to the finger. The same operation is done with the second bolt. The caliper is carefully removed from its guides, being careful not to damage the brake hose and handbrake cable. With a screwdriver, carefully shift the block along the plates and remove the outer block, and then the inner one. Next, the screwdriver is installed in the resulting gap between the guide pads and the plate. Squeezing the plate, it is removed from the guide. Before installing new pads, you should drown the piston in the cylinder. This can be done with a handy tool.
When the pads are removed, do not press the brake pedal. The piston can completely withdraw from the brake cylinder. This is how the rear brake pads are replaced on the Hyundai Solaris. At the rear, as well as at the front, a disc brake is installed.
Prices for service stations
In Moscow, the averagethe cost of replacing pads is from 600 rubles per pair for disc brakes and from 1000 rubles for a pair of drum pads. The prices are more than democratic, and the work is carried out by professional car mechanics who take into account all the subtleties and nuances of replacing brake pads with a Hyundai Solaris. The price also includes cleaning the calipers or drums, lubricating the guides, checking the system.
Conclusion
A good brake system is the key to safe car operation. If during use one or more symptoms of wear of the pads appear, you should urgently check their condition and, if necessary, replace the brake pads on the Hyundai Solaris with your own hands or with the help of specialists from the service station.
Recommended:
Replacing the timing belt on Lanos with your own hands: features of the work
In the article you will learn how the timing belt is replaced on Lanos. The state of this element must be monitored as closely as possible, since literally everything depends on it - both your financial well-being and the operation of the engine. The fact is that a broken belt can lead to the breakdown of several valves, and the cost of repairs is quite high. Some motorists naively believe that Lanos is a cheap car with nothing to break
Replacing the bendix on the car starter with your own hands
Bendix (aka overrunning clutch) is a mechanism designed to transmit torque from the starter rotor to the engine flywheel, as well as to protect the starter from high engine speeds. The element is highly reliable and fails quite rarely, but breakdowns do occur. A common cause of failure of the mechanism is the natural wear of the internal elements of the mechanism and springs. Let's see how the bendix is replaced if it is broken
Replacing the timing chain on the Chevrolet Niva with your own hands: step by step instructions with a photo
One of the most important components in an engine is the timing system. Today, manufacturers are increasingly switching to belt drive. However, many domestic cars are still equipped with a chain gas distribution mechanism. Chevrolet Niva is no exception. The manufacturer recommends replacing the timing chain on the Niva Chevrolet every 100 thousand kilometers
Replacing the timing belt with your own hands
GRM is a very important and responsible unit in the design of any car. It is he who is responsible for the accuracy and correct opening of the valves. To date, most engines are equipped with a timing chain drive. It is driven by a crankshaft
Replacing the shock absorber struts at the service station and with your own hands
Replacement of shock absorber struts is carried out in pairs: if the right one is out of order, then the left one must also be changed. This applies to both the rear and front axles of the car. If the breakdown occurred due to natural wear and tear, it is recommended to install new supports