2024 Author: Erin Ralphs | [email protected]. Last modified: 2024-02-19 11:42
Fuses for the UAZ-"Hunter" were modernized, completed along with the development of the progenitor of this model of the domestic car. The first model of the predecessor left the assembly line under the UAZ-64 brand. Further development brought many changes to this line of military vehicles, which were later adapted for civilian use. The new vehicle is equipped with modern units and assemblies, practically does not resemble its ancestors, and is focused on meeting all modern requirements and standards. Below is a diagram and designations of the main fuses.
- Start switch terminal.
- Outdoor lighting elements.
- Heated fuel filter element.
- Glow plugs.
General information
Updates fully apply to the fuses on the UAZ-"Hunter". The on-board network is equipped with an electronic autonomous diagnostic system, which helps to significantly simplify the process of identifying faulty machine mechanisms that have an electromechanical orientation. Fusible inserts, together with tape analogs, reliably protect the on-board electrical circuit. exit fromthe construction of any element indicates a failure in the operation of certain nodes or the appearance of defects in them.
Overload and short circuit protection
Important elements of protection of units and assemblies aggregated with the vehicle's on-board network are 26 fusible links. The fuses are combined into two compact blocks, which are located in the cabin of the UAZ-Hunter. They are located on the left side of the steering column. To facilitate the operation of the elements, a backlight with a switch is provided, mounted in the upper compartment of the mounting bracket.
There are belt-type fuses under the hood of the vehicle. Their place is the engine shield. By design, power relay blocks differ from each other. On models 315143/315148, this is a BPR-4.03 type system (with four tape elements), and other modifications are equipped with a BPR-2Mz design with a pair of tape inserts.
Features
The top cover of both blocks is equipped with a special niche in which four spare elements of the required rating are located. The camera itself is closed with a safety bar. Diesel versions of the car in question are additionally equipped with fuses for the UAZ-Hunter type M150 with a relay.
The system of fusible links BPR-13.02 includes 13 fuses that differ in rating. The current value is indicated on the housings of the elements, which are painted in different colors. In the provided compartment of the UAZ-Hunter cabin, a pair of such blocks is mounted on the dashboard. These insertsdesigned to protect electrical circuits and circuits.
Replacement of defective elements
Before you change a blown fuse, you should determine the cause of its failure. This will help to solve the problem correctly and quickly. When checking inserts, do not use metal tools. They can cause a short circuit in the circuits of the onboard electrical equipment. It is advisable to remove the defective part with special plastic tweezers.
The following points are prohibited when working with UAZ-Hunter fuses:
- The use of home-made analogues, the so-called bugs, as well as fuse-links that differ in nominal value or do not correspond to the block design.
- Use fuses that have an operating current that does not meet the parameters established by the regulations for this vehicle.
- Perform test of the investigated circuits for the occurrence of a spark by shorting the wires to the ground of the vehicle body.
UAZ-"Hunter" fuse diagram
Below is a diagram of the fusible links of the machine in question and the designation for it.
- K1 - low beam control relay.
- K2 - a similar element of fog lights.
- K3 - high beam control.
- K4 - rear window wiper relay.
- K5 - rear fog element fuse.
- 1 - socket.
- 2 - interrupter of the signaling device "turn signals".
- 3 snowplow breaker.
- 4 - fixing bracket.
What do fusible and tape inserts protect?
UAZ-"Hunter" fuse block provides protection for the following components and assemblies:
- Dimensional and main lighting elements.
- Turn indicators.
- Cigarette lighter.
- Beep.
- "Dvornikov".
- Indoor lighting.
- Brake warning lights.
- Reserve equipment.
- Cabin heaters.
- Radio equipment.
- Additional heating pump.
- Devices and indicators.
In closing
It can be noted that the fuses of the UAZ-"Hunter" car are very important elements. They allow you to pay attention to a particular malfunction in a timely manner and eliminate it. This helps to extend the working life of the main components of the machine and parts responsible for the safety of the driver and passengers.
Recommended:
Air suspension device: description, principle of operation and diagram
There are many systems and mechanisms in the design of a car. One of these is the chassis. It can be dependent and independent, on longitudinal and transverse levers, with springs or springs. In today's article we will talk about the air suspension device, its principle of operation and other features
Oil cooler "Gazelle" - description, device, diagram and reviews
Everyone knows that the cooling system is a very important element in any car. Usually, it means a liquid engine cooling system. But I must say that in modern machines there are a number of other systems. What applies to them? This can be transmission fluid cooling (if the car is equipped with automatic transmission), or engine oil. We will talk about the last system today, using the example of a commercial GAZelle car
VAZ-2115, fuses: device, circuit and features
Information about where the fuses are located and what they are used for in the VAZ-2115. Their design, designation features, malfunctions, replacement process are described
Car fuses
Car fuses - it would seem such a small detail. However, a lot depends on it. Sometimes, if the fuse blows, the whole car can also blow
Coolant circuit diagram. Engine cooling system diagram
Every car uses an internal combustion engine. Liquid cooling systems are widely used - only on the old "Zaporozhets" and the new "Tata" air blowing is used. It should be noted that the coolant circulation scheme on all machines is almost similar - the same elements are present in the design, they perform identical functions
