2024 Author: Erin Ralphs | [email protected]. Last modified: 2024-02-19 11:42
A punctured tire, shock absorber repair, brake repair, or muffler repair leaves many riders wondering how to remove a rear wheel on a scooter. This is more difficult to do than it seems at first glance. Although the second wheel is attached with just one nut, this operation may require special skills and knowledge.
Reasons for removing the rear wheel
The scooter, like any other vehicle, is subject to the laws of physics. Parts wear out and need to be repaired. Vehicle wheels are no exception. At first glance, removing the rear wheel from the moped is as easy as shelling pears. And yes, it's only held on by one screw. But this is a misleading impression. To get to the rim of the rear wheel, the owner will have to sweat a lot, removing most of the plastic and parts.
The reasons for removing the rear wheel of a scooter can be very diverse. Most often this is a flat tire, because few of the motorists at least once did not run a wheel onsharp object. But in the back of the scooter, in addition, there are many important parts, to access which you will need to disassemble half of the vehicle. And what else could be the reason for the repair with the dismantling of the rear wheel? List:
- Faulty brake pads. Brakes are the most important part in a motorcycle. If they don't work well, you need to fix the problem as soon as possible.
- Replacing the old wheel with a new one.
- Wheel balancing.
- Replacing the gear shaft.
- Disc painting.
- Setting the drum brake.
- Replacing a worn or punctured wheel.
Tools for the job
Before you remove the rear wheel on a scooter (150 cm³), you need to find the tools that are indispensable for repairs. You will need:
- socket wrench;
- clean rag;
- wood block.
A little luck and patience will help you finish your job faster.
Rear wheel removal instructions
How to remove the rear wheel from the scooter? The quickest way to figure this out will be the step-by-step instructions below:
- Place the scooter so that the rear wheel spins in the air.
- Remove the muffler. To do this, dismantle the seat and plastic, and then unscrew the nuts that hold the muffler. It is important not to remove them completely, but only loosen them.
- Unscrew the nuts securing the muffler to the cylinder with a socket wrench. Take it off the scooter. Atthis may lose the paranitic gasket, so be careful.
- If the muffler is dirty, it can be cleaned of soot and dirt. To do this, heat the outside with a blowtorch, and walk inside with a stiff metal brush. After all the manipulations, it is better to cover the muffler exhaust port with a clean cloth so that foreign particles do not get into it.
- Most mopeds have a monoshock. If your model has two of them, and they are located in the rear, you need to unscrew the nuts and dismantle them.
- If you have a rear disc brake, you need to do the same steps: carefully unscrew the brake caliper and move it to the side.
- And now you can proceed directly to the removal of the wheel. Loosen the carrier nut with an impact wrench. If this is not at hand, a regular screwdriver will do. But in this case, it is recommended to fix the wheel with a wooden beam.
- Remove the wheel from the spline.
Reverse the above steps to install the wheel.
Honda Scooter Repair
Japanese scooter Honda has long been in the top three best-selling vehicles with engines up to 150cc. Modern design, thoughtful and comfortable seat, agile chassis, fuel-efficient engine make Honda a favorite of many.
The undoubted advantages of the scooter include a liquid cooling system, a V-shaped transmission, and4-stroke engine with one cylinder. Honda mopeds consume about 2.5 liters per 100 km, and speeds can reach up to 100 km/h.
When riding off-road, moped owners often run into sharp objects that can damage tires. But removing the rear wheel on a Honda scooter can be difficult because of the cinder that sticks to the splines, which glues the parts together and makes the dismantling process difficult. In this case, experienced scooters advise spraying with WD-40, and then gently tapping the wheel closer to the center through a piece of wood.
Troubleshooting the Racer scooter
The Racer company entered the world market quite recently. Nevertheless, its products have already attracted motorists. A distinctive feature of this scooter is a kick starter that allows you to start it even with a dead battery. Fuel consumption per 100 km ranges from 2 to 5 liters. The 4-stroke engine has an electronic injection system and can reach speeds of up to 80 km/h.
When repairing wheels, two drum brakes installed at the rear and front make it difficult to remove them. Therefore, the question of how to remove the rear wheel on the Racer scooter is very relevant. To do this, you need to follow the steps described in the "Instructions" chapter, but with one amendment. Before removing the wheel itself, you need to loosen the brake cable that "sits" on the pads. After that, the procedure should go without much difficulty.
How to remove the rear wheel on a scooterIrbis
Another brand of scooters with engine capacity up to 150 cm³ is Irbis. The products of this brand are characterized by brutal design, two powerful headlights in front and bright colors. Seeing such a scooter on the road, you will not confuse it with anything. The largest models by cubic meter can reach speeds of up to 90 km / h. Disc brakes bring it to a quick stop in the event of extreme braking. Oil cooling keeps the motor from overheating.
Reinforced suspension with two shock absorbers can cause a lot of problems when removing the rear wheel. To access the tire, you will have to first unscrew the muffler mounts, and then the rear brake. Irbis scooters are equipped with a monoshock absorber, so there should be no problems in this part.
Recommendations from mechanics
You can find a lot of recommendations and discussions on how to remove the rear wheel on a scooter. Experienced motorists recommend using WD-40 penetrating lubricant (or, in extreme cases, gasoline) to facilitate repairs, and thoroughly clean and degrease the parts before installing. It is also strongly advised to lubricate the splines with grease. After installing the nut, it is recommended to tighten it strongly, jerkily, but without bumps. To hold the wheel in place, instead of a bar, you can use a CVT cover that will prevent it from turning.
As a last resort, if you are unable to dismantle the wheel yourself, experts recommend contacting the nearest trusted service. The same is worthto do if, after removing the parts, you find serious damage on one of them.
Results
Every scooter needs repair from time to time. A malfunctioning vehicle not only interferes with a comfortable ride, but also endangers the life of its driver. Repairing a scooter with your own hands is quite simple, if you sit down beforehand and properly understand the details. Sometimes the process can stall at some element, then it is recommended to carefully follow the entire sequence of steps from the very beginning - perhaps a mistake was made somewhere. When replacing the rear wheel, you need to take your time and be careful, and then you will succeed.
Success in repairs and good luck on the roads!
Recommended:
How to drain gasoline from a car tank? Accessories and step by step instructions
Probably, there is not a single driver who did not get into such trouble as having to drain the fuel from the car's tank. It is very important to perform this action according to the safety regulations, and also to know which of the existing methods is suitable for your car
Do-it-yourself plastic car parts repair: methods and step-by-step instructions
Repair of plastic car parts: methods, instructions and preparation. Where can I repair plastic parts in the car. How to repair plastic in the car yourself. Do-it-yourself repair of plastic car body parts. Professional repair of plastic car products in St. Petersburg and Moscow
Replacing the rear pads on the "Prior": step by step instructions, features, tips
Nothing lasts forever in a car - many parts are consumables. The same applies to the rear brake pads. During the operation of the car, they will certainly wear out. Periodically check their condition and replace if excessive wear. Let's see how the replacement of the rear pads on the Priore is done. Every car enthusiast can cope with this task
How to remove water from a car gas tank: methods and step by step instructions
Let's try to figure out how to remove water from a car's gas tank and do it as safely as possible. Both for the driver and for the system itself. We will also figure out why moisture penetrates the fuel compartment and how to avoid it
How to set up a carburetor on a scooter: step by step instructions
The fuel supply system needs periodic maintenance. Her work depends on it. How to set up a carburetor on a scooter, every owner of such a vehicle should know
